①斷電同時按住“＋”鍵和“－”鍵再接通電源蜂鳴器鳴叫兩聲速凍及自動運行指示同時點亮冷藏溫度顯示處顯示“Cl‘’（其余均不顯示）進入維修測試程序
②按“設定選擇”鍵，冷藏溫度可循環顯示“Cl C7”當顯示“Cl”時，按“確認，繼電器I（壓縮機）閉合，其他繼電器斷開；當顯示“C2”時，按“確認”向電磁閱I施加正向脈沖，其他繼電器斷開；當顯示“”時，按“確認”，向電磁閥E施加正向脈沖，其他繼電器斷開；當顯示“C4”時，按“確認”，冷凍顯示冷藏室實測溫度，所有繼電器斷開；當顯示“cs”時，按“確認”，冷凍顯示軟凍室實測溫度，所有繼電器斷開；當顯示“C6”時，按“確認”，冷凍顯示冷凍室實測溫度，所有繼電器斷開；當顯示“C7”時，按“確認”，冷凍顯示冷藏化霜傳感器溫度，所有繼電器斷開關閉電源將結束測試程序若內無任何按鍵操作也將結束測試并恢復正常程序
2. 故障指示：故障時通用信息和對應的分項信息同時閃爍如表5-2所示
3.顯示面版的拆卸
在顯示面板的下部一條邊上有兩個缺口將廢鋼鋸條一端磨口井去銳角，用此端插入顯示面板下部一條邊上的缺口處慢慢撬出顯示面板操作時要注意不要將門體的棒層破壞
4.維修時的注意事項
1）此制冷系統灌注為R600a制冷劑，維修制冷系統時一定要做好安全防火工作；系統修好后配接毛細管時一定按管上做的標記配管，不能接錯，否則會導致不制冷、不停機
2）此系統用的脈沖閥施加的電流為半波脈沖，所以不能直接用施加220V電壓的方法試脈沖閥是否正確工作
